Source Motorized Flow Controls

Oilpath Hydraulics Pty Ltd are the authorised Australian distributors for Source Products

The Source Motorized Flow Control provides economical and simple electric remote control for flows up to 50 GPM. It uses a 12 volt DC motor to open or close a rotary spool valve. The flow rate is changed by providing a 12 volt signal to either increase or decrease valve opening. In its simplest form, the control element is a DPDT three-position momentary-contact toggle or rocker switch, or two DP momentary-contact push buttons.

If a more sophisticated control is desired, the loop can be closed by using a control amplifier and relay circuit in conjunction with feedback from a flow or speed sensor.

The valve requires no power to maintain its flow setting. A 12 volt DC signal is applied only while changing the flow rate and then shut off to hold flow rate at the desired setting. In the event of a power failure or system shut down, the valve will remain at its current flow setting until power is restored and a command signal is once again applied. Valve design allows for manual over-ride in case of electrical failure.
The valve is internally protected and will automatically shut down the internal drive when either the full open or full closed positions are reached.


	F E A T U R E S • Internally protected • Requires no power to maintain setting • Safe • Flexible • Efficient • Simple to use • Economical DESCRIPTION • MFC-10 and MFC-16 valves are cartridge design and fit generic 10-2 and 16-2 cavities respectively.
F10_ _ _ _ (generic 10-2)
	OPERATING PRESSURE • 3000 psi (5000 psi with factory approval) FLOW RATING (Based on 100 psi with valve fully open) • 0-5 GPM MFC-10-5-12V- • 0-15 GPM MFC-10-15-12V- • 0-20 GPM MFC-16-20-12V- • 0-35 GPM MFC-16-35-12V- • 0-50 GPM MFC-16-50-12V- OPERATING SPEED (Fully closed to fully open) • 1 to 48 seconds • See catalog: Motor Spec Page (A-1) VOLTAGE** • 12V DC • 24V DC
F16_ _ _ _ (generic 16-2)
	CURRENT DRAW • Less than 120 MA typical @ 12V DC CARTRIDGE WEIGHT • MFC-10 (T13A): 1.3 lb. • MFC-16 (T16A): 1.6 lb. CONSTRUCTION • Nose, body and spool: steel • Exposed parts plated • Motor container assembly: anodized aluminum
F13A_ _ _ _ (Sun T13A)
	Download Data Sheets Source Fluid Power Gen. 11 Motor Specification Sheet Motorized Flow Controls Generic 16-2 Motorized Flow Control Valve F10 Generic Motorized Flow Control F10 with line body Motorized Relief Valve
F16_ _ _ _ (Sun T16A)
	Download Motorized Flow Control Valve with Pressure Compensation Data Sheets Model OP700 Model OP701 Download Motorized Priority Flow Control Valve with Pressure Compensation Data Sheets Model OP720 Model OP721 Download Motorized Flow Control Valve with Unloader & Relief Data Sheets Models OP722 and OP723
MFC Performance - Pressure Drop vs. Flow



	Download Data Sheets H10 Manual Flow Control to 15 GPM H20 Manual Flow Control to 120 GPM H16 Manual Flow Control to 50 GPM HPC16 Pressure Compensated (Bypass) Flow Control to 45GPM
Manual Fluid Controls

MFC OPTIONS AND ACCESSORIES

Panel mounted gage to show relative position of any Motorized Flow Control valve (reading in % of flow 0-100). Requires Feedback (FB) option on Motorized Flow Control. Custom dial faces available. Conforms to SAE standard for fuel sender.	Download Data Sheets MFC Accessories SFP25585 Single Valve Controller with Gauge SFP25587 Dual Valve Controller with Gauges


Closed Loop Control Module to allow potentiometer controlled position setting of any Motorized Flow or Pressure Control valve. Kit includes Control Module, Potentiometer and instructions. Wire connectors are optional. Requires Feedback (FB) option on Motorized Flow Control. Optional switch can move valve full open or full closed without changing command position.	Download Data Sheets PEM-DMC Control Board SFP25660 Single Valve Controller SFP25657 Dual Valve Controller SFP25726 Dual Valve Controller with Blash Function

Phone: 08 8277 4933 Free Call: 1300 787 571

Address: PO Box 132 , Edwardstown, SA, Australia 5039